Campbell PC208W Manual do Utilizador

MicroMet MBTU10X Version 1.05 Installation and Operation Manual Revised 4.26.02 Micro Specialties, Inc. P.O. Box 871077 Wasil

MicroMet Manual Pg. 7 Operation MicroMet Observations. The top MicroMet printed circuit board has five Light Emitting Diodes (LED) That can tell

MicroMet Manual Pg. 8 MicroMet Commands - MBTU10X Rev 1.05 The Micromet command structure is simple and concise. All commands are terminated wi

MicroMet Manual Pg. 9 T – Test transmission. MicroMet will turn on its transmitter and attempt to send whatever is in its immediate transmit queu

MicroMet Manual Pg. 10 Warnings and Advisories MicroMet may issue various advisories or warnings to indicate a change in system status. Advisori

MicroMet Manual Pg. 11 Communications Cycle MicroMet MBTU10X operates as a power conserving remote node in a ‘star’ network topology. The networ

MicroMet Manual Pg. 12 Understanding Communications Statistics (Stat Command) RXSP Signal Presence – this is the number of times the radio recei

MicroMet Manual Pg. 13 HIVSWR High Voltage Standing Wave Ratio – this means that during a transmit cycle, MicroMet’s transmitter hardware dete

MicroMet Manual Pg. 14 Checking MicroMet Communications Performance 1. Connect the MicroMet cable between the PC and J3 of the MicroMet unit. 2.

MicroMet Manual Pg. 15 CR10X Datalogger Operations Loading a CR10X program from PC208W When a new program needs to be installed in the CR10X dat

MicroMet Manual Pg. 16 Setting up a New Data Station in PC208W PC208W is Campbell Scientific’s CR10X maintenance program that runs under Windows.

Index Conventions Used in Manual 1 About MicroMet 1 CR10X Processing for MicroMet 3 Installation Site Selection

MicroMet Manual Pg. 17 Verifying Sensor Data with PC208W Campbell Scientific’s Windows based Data Logger maintenance program, PC208W can be used

MicroMet Manual Pg. 18 Site Visit Normal Site Visit Procedures Whenever a visit is made to a MicroMet data site, the following checks should be

MicroMet Manual Pg. 19 Troubleshooting No Data Reports Received at AMBCS Before troubleshooting, read and understand MicroMet Observations (pg 6

MicroMet Manual Pg. 20 No CR10X Data Messages ! If you suspect that the CR10X is not producing any data messages, you should connect your PC to

MicroMet Manual Pg. 21 Resolving Bad Sensor Readings (CR10X) ! Connect your PC to CR10X CSIO, and run PC208W. ! Use the NUMERIC DISPLAY tab

MicroMet Manual Pg. 22 Replacing the CR10X Data Collector Canister The CR10X Data Collector is the unit which interfaces to, and collects data f

MicroMet Manual Pg. 23 Installing the new CR10X canister ! Examine the replacement CR10X canister. Notice that it has two connector plugs which

MicroMet Manual Pg. 24

MicroMet Manual Pg. 25 CR10X Files All CR10X files are maintained by Campbell Scientific’s PC208W program. PC208W usually installs files in the

MicroMet Manual Pg. 26

Troubleshooting No Data Reports Received at AMBCS 19 No CR10X Data Messages 20 Resolving bad Sensor Readings (CR10X) 21 Replaci

MicroMet Manual Pg. 1 Conventions Used in This Manual MicroMet and CR10X commands are printed in bold face for clarity. ‘Warning:’ indicates tha

MicroMet Manual Pg. 2

MicroMet Manual Pg. 3 CR10X processing for MicroMet Version 1.03 and above The CR10X, when used with the MicroMet MBTU10X for data transport, mu

MicroMet Manual Pg. 4 Installation Site Selection Considerations Communications Window Aperture What is the horizon in the direction of radiati

MicroMet Manual Pg. 5 Installing the MicroMet Communications Unit MicroMet data communications units come in two varieties, one with a 300 watt t

MicroMet Manual Pg. 6 Setting up a Windows95/98 Computer to talk with the MicroMet Normal operation of the MicroMet unit is fully automatic, and