Campbell SAT ARGOS Manual do Utilizador Página 207
- Página / 394
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
ZENO
®
-3200 USER MANUAL
Coastal Environmental Systems (206) 682-6048
Page 199
When the Selectable Transmit and Log data field is used, ZENOSOFT
®
will
store the message number which generated that output message immediately
after the Timestamp with each Data Record.
222
Care must be taken when using the Selectable Transmit and Log data field
because when downloading data, ALL Data Records are dumped—
regardless of which message number logged the Data Record.
Coastal Environmental Systems recommends that you use some means to
identify which message number logged each Data Record. You can create a
separate Data Output Record, using the Message Number Field Type
Code
223
, or by using another Selectable Transmit and Log data field to store
a user-specified identification number.
Further, when multiple output messages are being logged, information
provided by option C in the Data Retrieval Menu
224
may not be accurate,
because ZENOSOFT
®
cannot predict when extra output messages are going
to be logged.
However, these extra messages in NO way interfere with data collection or
retrieval!
10.7. SETTING OUTPUT MESSAGE SCHEDULES AND DESTINATIONS
Since the ZENO
®
-3200 can transmit up to four different output messages,
the ZENO
®
-3200 provides the means to configure which COM port each
output message is transmitted on, as well as the time of transmission for
each output message.
The Output Message Timing Menu lets you control when, and from which communications port, each of
the up to four output messages will be sent. To access the Output Message Timing Menu, type
O{ENTER} from the Zeno Program Menu. Your screen should look something like this:
222
The Timestamp is always the first value stored in each Data Record and requires 4 bytes. The message number
is stored using a single byte.
223
Refer to Section 10.6.3.
224
Refer to Section 4.2.
- P/N: 0302116012, Revision C 1
- Table of Contents 3
- Acknowledgements 8
- 1. INTRODUCTION 9
- 1.3. ZENO 10
- -3200 SPECIFICATIONS 10
- 1.3.1. Analog Inputs 10
- 1.3.2. Digital I/O Ports 10
- 1.3.5. ADC Conversion Rates 11
- Refer to Section 12.1.4 12
- 2. ZENO 13
- -3200 BASICS 13
- 2.3. ZENO 16
- -3200 MEMORY 16
- 2.3.1. RAM 17
- 2.3.2. EEPROM 17
- 2.4. THE USER INTERFACE 18
- 2.4.2. Online Help 19
- 32 bit CPU 20
- 3. TUTORIAL: BASIC 21
- -3200 OPERATION 21
- Since many ZENO 22
- Refer to Section 2.2 25
- Refer to Section 2.3.2 27
- Refer to Section 3.1 32
- Refer to Section 8.1 33
- Discussed in Section 3.2.3 34
- Discussed in Section 3.2.4 34
- Discussed in Section 3.2.5 34
- Refer to Section 10.3.6 38
- Refer to Section 2.1 39
- Refer to Section 10.4.1 45
- 10.4.1 46
- Refer to Section 10.4.2 47
- Refer to Section 10.6.4 53
- Refer to Section 10.2 57
- 4. RETRIEVING LOGGED 59
- 4.1. DATA RETRIEVAL OPTIONS 60
- Refer to Section 4.1.1 63
- Kermit file transfer 65
- Refer to Section 10.6.5 67
- CCSAIL protocol 68
- 4.6.2. The ZENO 71
- 5. INTERNAL ZENO 77
- SETTINGS 77
- 5.1. ZENO 78
- -3200 SYSTEM DATE AND TIME 78
- VERSION NUMBER 79
- 5.4. CONTACT INFORMATION 79
- 5.5. ZENO 79
- 5.7. COMPASS SENSOR USAGE 81
- 6. COMMUNICATION 82
- INTERFACES 82
- RS232, RS232H, RS485, RS422 85
- 6.2. DIRECT TERMINAL ACCESS 87
- 6.3. HARDWARE HANDSHAKING 87
- 6.4. TELEPHONE MODEMS 88
- 6.4.1. ZENO 88
- -3200 Modem Configuration 88
- ZENOSOFT 90
- 6.4.2. MODEM SETTINGS 91
- Computer Modem A Modem B 93
- ZENO 3200 93
- PSTN/PBX 93
- 6.4.3. CABLE PIN-OUTS 95
- 6.5. CELLULAR MODEMS 96
- Cellular Modem 98
- Manufacturer 98
- CDPD Sierra Wireless MP200 98
- 6.6. RADIO COMMUNICATIONS 102
- 6.6.5. Push-To-Talk (PTT) 107
- 6.6.6. Response Delay Time 107
- 6.6.7. Data Packetization 108
- 6.7.2. Data Download 109
- 6.7.6. ZENO 114
- -3200 Configuration 114
- GMT is Greenwich Mean Time 116
- Refer to Section 11.3.3 116
- 6.7.10. Random Transmissions 117
- 6.7.11. GOES Binary Format 117
- Refer to Section 10.6 118
- 6.8.2. ARGOS Coverage 119
- 6.8.3. Data Recovery 119
- 6.8.5. ZENO 120
- 6.8.6. ARGOS Binary Format 122
- 6.9. PASSTHROUGH MODES 122
- Refer to Section 6.9.3 124
- Refer to Appendix A 127
- 6.10. REPEATER CAPABILITY 128
- Refer to Section 4.6 129
- Refer to Section 5.5 129
- 6.11.1. Overview 132
- 6.11.4. Wiring Diagram 137
- INTERFACE 138
- 7. MONITORING & 140
- CALIBRATING SENSOR 140
- Refer to Section 10.3.13 141
- Refer to Section 2.4.2 142
- 8. ZENO 146
- -3200 ACCESS 146
- PRIVILEGES 146
- 9. UPLOADING AND 149
- DOWNLOADING AN 149
- ENTIRE CONFIGURATION 149
- ZENOSOFT 153
- VERSIONS 153
- 10. ZENO 155
- CONFIGURATION 155
- SPECIFICS 155
- 10.3. DEFINING THE SENSORS 156
- Refer to Section 12.2 157
- 10.3.1. Analog Sensors 158
- 10.3.2. Digital Sensors 161
- Refer to Section 6.12 173
- Refer to Section 10.3.5 175
- C is given by the equation: 180
- -3200 USER MANUAL 184
- Page 176 184
- 10.5. DEFINING CONSTANTS 188
- Refer to Section 11 189
- Refer to Section 2.3.1 189
- Refer to Section 4 189
- Page 186 194
- Refer to Section 10.4.4 199
- Refer to Section 5 203
- Refer to Section 5.6 203
- Refer to Section 4.4.2 203
- Refer to Section 10.6.3 207
- Refer to Section 4.2 207
- Refer to Section 6.1 208
- 11. ALARM MESSAGES 213
- Refer to Section 6.7 216
- Refer to Section 6.8 216
- 11.3. CONFIGURING THE ZENO 217
- ALARM MESSAGE 217
- Refer to Section 6.4 218
- Refer to Section 0 218
- Refer to Section 11.3 218
- Refer to Section 11.3.1 218
- 12. ADVANCED ZENO 222
- 3200 CONFIGURATION 222
- 12.1.2. The ZENO 223
- -3200 Internal Clock 223
- 12.1.4. ZENOSOFT 224
- and Multitasking 224
- Refer to Section 10.3.7 225
- -3200 To Measure All Sensor 227
- Records 227
- TNTNTNTNTNT 230
- Refer to Section 10.3.8 231
- 12.2.2. The Sensor Menu 232
- Refer to Section 12.2.3 233
- Refer to Section 12.2.2 234
- Refer to Section 9.1 238
- Refer to Section 9.2 238
- ", % and \ 243
- -3200'S 247
- (MULTIPROCESSING) 247
- 13. ELECTRICAL 249
- CONSIDERATIONS 249
- Converter 250
- Chassis 252
- 13.4. THE ZENO 253
- -3200 CPU BOARD 253
- 13.5. SERIAL PORT WIRING 253
- A. CONSTANTS 261
- CONVERSIONS & ASCII 261
- 2. CONVERSION CONSTANTS 262
- 3. ASCII CODES 264
- Page A-6 266
- B. ZENO 267
- -3200 MENU 267
- Page B-2 268
- Page B-3 269
- Page B-4 270
- Page B-5 271
- Page B-6 272
- Page B-7 273
- Page B-8 274
- Page B-9 275
- Page B-10 276
- C. SENSOR 277
- CONFIGURATIONS 277
- 3. BAROMETRIC PRESSURE 280
- 4. 20MA CURRENT LOOP 281
- PLATINUM RTD 286
- 8. SDI-12 SENSOR 289
- DEFAULT 290
- 11. ELLIASON CEILOMETER 294
- 12. VAISALA 299
- 425AH OR 425AHW ANEMOMETER 299
- D. ZENO 305
- -3200 PROCESS 305
- Refer to Section 3.1.3 307
- 1.4. Block Average Process 308
- 1.5. Accumulation Process 309
- 1.6. Rate of Change Process 310
- 1.7. Differential Process 310
- 1.9. Collection Process 311
- 1.10. Trend Data Process 312
- Refer to Section 5.7 314
- Refer to Section 10.3.4 319
- Refer to Section 5.8 319
- 2.6. Rainfall Process 320
- 2.7. Dewpoint Process 321
- 396.6106 323
- 0091379024.066082.26 323
- 089 1 1 324
- 325
- 328
- 3. ALARM PROCESSES CATEGORY 333
- 3.2. Data Range Process 335
- 3.3. Alarm Process 335
- 3.4. Data Time-out Process 336
- 3.5. Alarm Reset Process 336
- 3.9. Multiple Alarm Process 339
- Refer to Section 11.3.2 340
- Refer to Section 10.4.5 341
- 3.13. Timed Event Process 342
- 3.15. Static Alarm Process 343
- 4.1. NTC Thermistor Process 343
- ABRC R ln (ln ) 344
- 4.3. Thermocouple Process 345
- 4.5. UV Biometer Process 347
- TTKTEPIR 348
- 5.16. Data Rounding Process 351
- E. CONFIGURATION FILE 353
- CONTENTS 353
- Refer to Section 9.4 354
- - Zero-offset check period 356
- F. LIBRARY OF CCSAIL 359
- COMMANDS 359
- 2. RESPONSES 360
- ERRORnnn 361
- 3. TIME COMMANDS 361
- 4. DATA RETRIEVAL COMMANDS 362
- Refer to Section 4.3 363
- Refer to Section 4.1.5 363
- Refer to Section 4.1.2 364
- 5. USER INTERFACE ACCESS 365
- Refer to Section 10.8 367
- Refer to Section 6.9.1 367
- Refer to Section 6.9.2 367
- Refer to Section 10.5 370
- Refer to Section 6.10 371
- Refer to Section 10 377
- G. INDEX 381
- , 74, E-2 384
- Rain Data, D-16 389
- , 21, 24, 206, 220 390
- , 20, 21, 22, 51, 52, 220, B 390
Manuais e produtos relacionados com Software Campbell SAT ARGOS
Software Campbell BMP5 Informações Técnicas
(100 páginas)
(100 páginas)
Software Campbell PC208 Manual do Utilizador
(6 páginas)
(6 páginas)
Software Campbell PC208W Manual do Utilizador
(62 páginas)
(62 páginas)
Software Campbell PC208 Manual de Instruções
(133 páginas)
(133 páginas)
Software Campbell Baler Manual do Utilizador
(4 páginas)
(4 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.274 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais